You are here: Power tools,Air Sander,Electric Screwdriver,Riveter,Nutsert Gun,Torque Mete » Air Tool » Air Screwdrivers » Shut Off Series » STWA series gun type pressure plate type pneumatic torque screwdriver

product category

Tools Parts
- Pad
- Sandpaper
- Air Bit
- Spring Balancer
- Blind Rivet
- Hand Socket
- One Touch Coupler
- Rivet Nut
- Wheel
- Air Spray Gun
- Air Blow Gun

STWA series gun type pressure plate type pneumatic torque screwdriver

Share to:

STWA series gun type pressure plate type pneumatic torque screwdriver

Light in hand, no twisting
One-hand operation forward and reverse
push button switch
rear exhaust
Stop when the torque is reached

Availability:

Quantity:



Inquire Add to Basket

Model:
HC-31PB/41PB/51PBSTWA

Product Description

Pneumatic twist control screwdriver

Light in hand, no twisting
One-hand operation forward and reverse
push button switch
rear exhaust
Stop when the torque is reached

product data

model model	free speed Free Speed	net weight Weight	tool length Overall	air inlet Air Hose Size (Inside Dia)		Tightening torque range Torque Range		air consumption Average	noise noise
	RPM	kg	mm	mm	in	Kgf-cm	N m	m3/min	DB
HC31PB11STWA	1100	0.74	183	6.35	1/4	10~25	1.0~2.5	0.20	70
HC31PB17STWA	1700	0.74	183	6.35	1/4	10~20	1.0~2.0	0.20	70
HC31PB23STWA	2300	0.74	183	6.35	1/4	10~15	1.0~1.5	0.20	71
HC41PB08STWA	800	0.87	194	6.35	1/4	08~40	0.8~4.0	0.30	70
HC41PB15STWA	1500	0.87	194	6.35	1/4	10~30	1.0~3.0	0.30	70
HC41PB21STWA	2100	0.87	194	6.35	1/4	10~25	1.0~2.5	0.30	74
HC51PB04STWA	380	1.20	213	6.35	1/4	40~130	4.0~1 3	0.50	74
HC51PB05STWA	480	1.20	213	6.35	1/4	20~100	2.0~1 0	0.50	74
HC51PB08STWA	800	1.20	213	6.35	1/4	15~60	1.5~6.0	0.50	75
HC51PB17STWA	1700	1.20	213	6.35	1/4	15~35	1.5~3.5	0.50	75

Security requirements:
mechanical safety全instruction:2006/42/EC
Risk Assessment and RiskRisk reduction:ISO 12100
Security requirements:ISO 11148-6
Vibration level:ISO 15744
noise etc.Grade: ISO 28927

air toolInstructions for use and care

The instructions for use of pneumatic tools are to deliver dry and low-temperature compressed air through clean piping,Requires a three-point assembly between hard and rubber hose
1.Air tool oil:Regular rotation and permanent mechanical life for pneumatic tools,Be sure to add pneumatic maintenance oil.
(1)motor part:daily before use, please inject from the oil port after use2~3ccpneumatic lubricating oil/Pneumatic maintenance oil.
(2)clutch part:每1Months to wash the old butter out of the clutch,Then apply a generous amount of new butter,But if you inject too much butter,Please note that it will reduce the function!
with oil hole,Screws should be removed monthly,Add a little.
2.Air Compressor Management:
Pneumatic tools must use low-temperature clean and dry compressed air with a fixed air pressure and sufficient air volume.
(1)Air compressor
be usable2HPstandard compressor
(2)air pressure
Please use standard air pressure,5~7kg/cm2If higher air pressure is used,will enhance the ability,But it will shorten the life of pneumatic tools a lot,So please avoid.
(3)Elimination of impurities and moisture
Impurities and moisture in the compressor are eliminated even if,But hard tube and rubber tube,there will still be a little,Therefore, when loading and unloading pneumatic tool hoses and adapters, please try to remove impurities and moisture as much as possible.
3.air tool running:
(1)Please run freely for a few seconds after oil filling.
(2)engine running:
turn left and rightR壓,Buckle 機,It is the lever when locking the screwLpull the trigger,Do not switch in a slew.
(3)adjustment ability:
After tightening the screws,1/2turn around(約1秒)Rotary stop,Properly screwed in and it's over,Adjust the upper scale of the regulator,The necessary ability can be obtained.
(4)usual screws,約2~3can be installed in seconds,若5operation over seconds,Screws that cannot be loosened and screws that cannot be torqued,A higher capacity air tool should be used.
(5)when machinery falls from above,Don't knock, hammer, etc. indiscriminately,Please have it ruled out by a professional
(6)Rusted and cracked sockets,Please avoid using it.

product category

STWA series gun type pressure plate type pneumatic torque screwdriver

Quick Links Quick Navigation

Product Category Quick Navigation

Contact Us

E-mail Subscriptions