You are here: Power tools,Air Sander,Electric Screwdriver,Riveter,Nutsert Gun,Torque Mete » Air Tool » Air Screwdrivers » Shut Off Series » 90 Degree Elbow Straight Platen Type Pneumatic Torque Screwdriver

product category

loading

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

90 Degree Elbow Straight Platen Type Pneumatic Torque Screwdriver

  • Light in hand, no twisting
  • One-hand operation forward and reverse
  • push button switch
  • rear exhaust
  • Stop when the torque is reached
Availability:
Quantity:
  • HC-B0C welcomes all kinds of torque customization

Pneumatic twist control screwdriver
 
  • Light in hand, no twisting

  • One-hand operation forward and reverse

  • push button switch

  • rear exhaust

  • Stop when the torque is reached

90 degree elbow screwdriver

product data

model

model

free speed

Free Speed

net weight

Weight

tool length

Overall

air inlet

Air Hose   size

(Inside   Dia)

Tightening torque range

Torque   Range

air consumption

Average

noise

noise


RPM

kg

mm

mm

in

Kgf-cm

N m

m3/min

DB

HC40-03CC

1100

0.64

261

6.35

1/4

10~25

1.0~2.5

0.20

70

HC40-03CD

1700

0.64

261

6.35

1/4

10~20

1.0~2.0

0.20

70

HC40-03CLC

800

0.76

277

6.35

1/4

08~40

0.8~4.0

0.30

70

HC40-03CLD

1500

0.76

277

6.35

1/4

10~30

1.0~3.0

0.30

70


Security requirements:
mechanical safetyinstruction:2006/42/EC
Risk Assessment and RiskRisk reduction:ISO 12100
Security requirements:ISO 11148-6
Vibration level:ISO 15744
noise etc.Grade: I
SO 28927




air toolInstructions for use and care

The instructions for use of pneumatic tools are to deliver dry and low-temperature compressed air through clean piping,Requires a three-point assembly between hard and rubber hose
1.Air tool oil:Regular rotation and permanent mechanical life for pneumatic tools,Be sure to add pneumatic maintenance oil.
(1)motor part:daily before use, please inject from the oil port after use2~3ccpneumatic lubricating oil/Pneumatic maintenance oil.
(2)clutch part:1Months to wash the old butter out of the clutch,Then apply a generous amount of new butter,But if you inject too much butter,Please note that it will reduce the function!
with oil hole
,Screws should be removed monthly,Add a little.
2.Air Compressor Management:
Pneumatic tools must use low-temperature clean and dry compressed air with a fixed air pressure and sufficient air volume.
(1)Air compressor
be usable2HPstandard compressor
(2)air pressure
Please use standard air pressure,5~7kg/cm2If higher air pressure is used,will enhance the ability,But it will shorten the life of pneumatic tools a lot,So please avoid.
(3)Elimination of impurities and moisture
Impurities and moisture in the compressor are eliminated even if,But hard tube and rubber tube,there will still be a little,Therefore, when loading and unloading pneumatic tool hoses and adapters, please try to remove impurities and moisture as much as possible.
3.air tool running:
(1)Please run freely for a few seconds after oil filling.
(2)engine running:
turn left and rightR,Buckle  ,It is the lever when locking the screwLpull the trigger,Do not switch in a slew.
(3)adjustment ability:
After tightening the screws,1/2turn around(1)Rotary stop,Properly screwed in and it's over,Adjust the upper scale of the regulator,The necessary ability can be obtained.
(4)usual screws,2~3can be installed in seconds,5operation over seconds,Screws that cannot be loosened and screws that cannot be torqued,A higher capacity air tool should be used.
(5)when machinery falls from above,Don't knock, hammer, etc. indiscriminately,Please have it ruled out by a professional
(6)Rusted and cracked sockets,Please avoid using it.


 

       

Previous: 
Next: 

Quick Links

Product Category

Contact Us

Company: No. 831-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City 24261, Taiwan
Tel: +886-2-29063289
Fax: +886-2-29013777
mailbox1: fhc.tool@msa.hinet.net
mailbox2: airtool@fhctool.com
 
 
 

E-mail Subscriptions

If you are interested in our products, please leave your email address and keep an eye on our developments.
Copyright © 2022 HSIEH CHIEN AIR ACTIVATION CO., LTD.